Merge branch 'master' of https://twinetfs.visualstudio.com/_git/Tango

1 files changed, 116 insertions, 40 deletions

diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
index 837221274..5984618d9 100644
--- a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
+++ b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
@@ -48,15 +48,21 @@
         8 THREAD_LOAD_CLOSE_ROCKERS,
         9 THREAD_LOAD_CLOSE_DANCERS,                         //SEND DANCER MOTORS TO PRESET LOCATION, CHECK THAT THE DANCERS ARE ON THE THREAD
         10 THREAD_LOAD_CLOSE_LIDS,
-        11 THREAD_LOAD_RESUME_HEATING,
-        12 THREAD_LOAD_JOG_FEEDER_TO_MIDDLE_POINT,           //JOG THE FEEDER MOTOR UNTIL THE FEEDER DANCER IS AT MIDDLE POSITION
-        13 THREAD_LOAD_DRYER_LOADING,                        //START FEEDER PID, ROTATE LOADING ARM COUNTER THREAD DIRECTION X CIRCLES ACCORDING TO RML. FEEDER SPEED IS 40
+        11 THREAD_LOAD_JOG_FEEDER_TO_MIDDLE_POINT,           //JOG THE FEEDER MOTOR UNTIL THE FEEDER DANCER IS AT MIDDLE POSITION
+        12 THREAD_LOAD_DRYER_LOADING,                        //START FEEDER PID, ROTATE LOADING ARM COUNTER THREAD DIRECTION X CIRCLES ACCORDING TO RML. FEEDER SPEED IS 40
                                                              //KEEP NOTATION HOW MANY ROTATIONS IN THE DRYER
+        13 THREAD_LOAD_RESUME_HEATING,
         14 THREAD_LOAD_JOG_THREAD,                           //JOG THREAD SHORTLY TO MAKE SURE SPOOL IS RUNNING. REPORT END OF LOADING
         15 THREAD_LOAD_END
     }THREAD_LOAD_STAGES_ENUM;*/
     THREAD_LOAD_STAGES_ENUM LoadStages = THREAD_LOAD_INIT;
     ProcessParameters ProcessParametersClear,ProcessParametersRecover;
+
+    int32_t keepmicrostep;
+    int32_t keepkvalrun;
+    uint8_t CallbackCounter = 0;
+    uint8_t TimeoutsCounter = 0;
+
     uint8_t NumberOfDrierLoaderCycles = 0;
     uint32_t status = OK;
     uint32_t ControlId = 0xFF,PullerControlId = 0xFF,WinderControlId = 0xFF;
@@ -93,7 +99,7 @@
         FRESULT Fresult = FR_OK;
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
 
-        LoadArmInfo.LoadArmBackLash = 10;
+        LoadArmInfo.LoadArmBackLash = 5;
         LoadArmInfo.LoadArmRounds = 0xFF;
         Fresult = f_mkdir(SW_INFO_DIR);
         if ((Fresult == FR_OK)||(Fresult == FR_EXIST))
@@ -133,6 +139,7 @@
         ProcessParametersClear.headzone5temp  = 0;
         ProcessParametersClear.headzone6temp  = 0;
         ProcessParametersClear.dyeingspeed = 40;
+        ProcessParametersClear.dryerbufferlength = ProcessParametersKeep.dryerbufferlength;
         if (HandleProcessParameters(&ProcessParametersClear)!= OK)
         {
             LOG_ERROR (LoadStages, "Thread_Load_Init failed");
@@ -163,7 +170,7 @@
         }
         else*/
         {
-            Report("Thread_Load_Set_Load_Arm_To_Start_Position_Callback",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
+            Report("Thread_Load_Set_Load_Arm_To_Start_Position_Callback",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
             //storeLoadArmParameters();
             SetMotHome(HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM);  //set this point as the spool home
             LoadStages++;
@@ -173,6 +180,7 @@
     }
     uint32_t Thread_Load_Set_Load_Arm_To_Stopper_Callback(uint32_t deviceID, uint32_t BusyFlag)
     {
+
         if(PullerControlId != 0xFF)
         {
             MotorStop(ThreadMotorIdToMotorId[POOLER_MOTOR],Hard_Hiz);
@@ -192,7 +200,8 @@
         MotorStop(HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,Hard_Hiz);
 
 //        Report("Thread Load State Machine Callback.",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
-        Report("Thread_Load_Set_Load_Arm_To_Stopper_Callback",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
+        CallbackCounter = 0;
+        Report("Thread_Load_Set_Load_Arm_To_Stopper_Callback",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
         NumberOfDrierLoaderCycles=0;
         //storeLoadArmParameters();
         LoadStages++;
@@ -224,13 +233,21 @@
         //Use Notation How Many Rotations In The Drier, Or Check Against Stopper. Move Slowly
         return OK;
     }
-    uint8_t CallbackCounter = 0;
-    uint8_t TimeoutsCounter = 0;
+    uint32_t Thread_Load_Jog_Feeder_To_Middle_Point_Callback(uint32_t deviceID, uint32_t BusyFlag)
+    {
+        CallbackCounter--;
+        Report("Thread_Load_Jog_Feeder_To_Middle_Point_Callback",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
+        //storeLoadArmParameters();
+        LoadStages++;
+        ThreadLoadStateMachine(LoadStages);
+
+        return OK;
+    }
 
     uint32_t Thread_Load_HomingCallback(uint32_t MotorId, uint32_t ReadValue)
     {
-        Report("Thread Load State Machine Callback.",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
-        REPORT_MSG(MotorId, "Thread_Load_HomingCallback Motor Id");
+        Report("Thread_Load_HomingCallback",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
+//        REPORT_MSG(MotorId, "Thread_Load_HomingCallback Motor Id");
         if (CallbackCounter)
         {
             CallbackCounter--;
@@ -249,12 +266,12 @@
                 else
                 {
                     LoadStages++;
-                    if (LoadStages == THREAD_LOAD_LIFT_ROCKERS)
+                    if (LoadStages == THREAD_LOAD_CLOSE_ROCKERS)
                     {
-                        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_RLOADING,  MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].microstep);
-                        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_LLOADING,  MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].microstep);
-                        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].microstep);
-                        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].microstep);
+                        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_RLOADING,  keepmicrostep);
+                        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, keepmicrostep);
+                        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, keepkvalrun);
+                        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, keepkvalrun);
                     }
                     if (LoadStages != THREAD_LOAD_INITIAL_TENSION) //on this stage we should wait for user call
                     {
@@ -303,16 +320,18 @@
     uint32_t Thread_Load_Lift_Rockers(void)
     //Machine Is Ready. Send Message, Start Timer To Close Lids, Wait For Operator Response
     {
+        keepmicrostep = MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].microstep;
+        keepkvalrun = MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].kvalrun;
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
-        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, 1);
-        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, 1);
-        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, 35);
-        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, 35);
+        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, 8);
+        MotorSetMicroStep(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, 8);
+        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_RLOADING, 70);
+        MotorSetKvalRun(HARDWARE_MOTOR_TYPE__MOTO_LLOADING, 70);
         Task_sleep(10);
         CallbackCounter++;
-        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_RLOADING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].directionthreadwize, 50,  Motor_Id_to_LS_IdUp[HARDWARE_MOTOR_TYPE__MOTO_RLOADING], Thread_Load_HomingCallback,25000);
+        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_RLOADING,1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].directionthreadwize, 400,  Motor_Id_to_LS_IdUp[HARDWARE_MOTOR_TYPE__MOTO_RLOADING], Thread_Load_HomingCallback,20000);
         CallbackCounter++;
-        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_LLOADING,1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].directionthreadwize, 50,  Motor_Id_to_LS_IdUp[HARDWARE_MOTOR_TYPE__MOTO_LLOADING], Thread_Load_HomingCallback,25000);
+        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_LLOADING,1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].directionthreadwize, 400,  Motor_Id_to_LS_IdUp[HARDWARE_MOTOR_TYPE__MOTO_LLOADING], Thread_Load_HomingCallback,20000);
 
         return OK;
     }
@@ -334,9 +353,9 @@
     {
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
         CallbackCounter++;
-        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_RLOADING,1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].directionthreadwize, 300,  Motor_Id_to_LS_IdDown[HARDWARE_MOTOR_TYPE__MOTO_RLOADING], Thread_Load_HomingCallback,12000);
+        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_RLOADING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RLOADING].directionthreadwize, 300,  Motor_Id_to_LS_IdDown[HARDWARE_MOTOR_TYPE__MOTO_RLOADING], Thread_Load_HomingCallback,20000);
         CallbackCounter++;
-        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_LLOADING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].directionthreadwize, 300,  Motor_Id_to_LS_IdDown[HARDWARE_MOTOR_TYPE__MOTO_LLOADING], Thread_Load_HomingCallback,12000);
+        MotorMovetoLimitSwitch (HARDWARE_MOTOR_TYPE__MOTO_LLOADING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LLOADING].directionthreadwize, 300,  Motor_Id_to_LS_IdDown[HARDWARE_MOTOR_TYPE__MOTO_LLOADING], Thread_Load_HomingCallback,20000);
 
         return OK;
     }
@@ -388,13 +407,20 @@
     {
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
         CallbackCounter++;
-        MotorMovetoDancerPosition (HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDRIVING].directionthreadwize, 200, FEEDER_DANCER ,true, Thread_Load_HomingCallback,10000);
+        MotorMovetoDancerPosition (HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDRIVING].directionthreadwize, 100, FEEDER_DANCER ,true, Thread_Load_Jog_Feeder_To_Middle_Point_Callback,2000);
         return OK;
     }
 
     uint32_t Thread_Load_Dryer_MovetoEncoderPosition_Callback(uint32_t MotorId, uint32_t ReadValue)
     {
+        Report("Thread_Load_Dryer_MovetoEncoderPosition_Callback",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
         MotorSetMaxSpeed (HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, 200);
+        if(ControlId != 0xFF)
+        {
+            MotorStop(ThreadMotorIdToMotorId[FEEDER_MOTOR],Hard_Hiz);
+            RemoveControlCallback(ControlId, ThreadLoadControlCBFunction );
+            ControlId = 0xFF;
+        }
         if (CallbackCounter)
         {
             CallbackCounter--;
@@ -410,17 +436,18 @@
         else
             LOG_ERROR(MotorId, "Thread_Load_HomingCallback Callback is already 0");
 
+        return OK;
     }
     uint32_t Thread_Load_Dryer_Loading_Callback(uint32_t MotorId, uint32_t ReadValue)
     {
-        Report("Thread Load State Machine Callback.",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
-        if(ControlId != 0xFF)
+        Report("Thread_Load_Dryer_Loading_Callback",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
+        Report("Thread_Load_Dryer_Loading_Callback details",__FILE__,__LINE__,MotorId,RpMessage,CallbackCounter,0);
+        /*if(ControlId != 0xFF)
         {
             MotorStop(ThreadMotorIdToMotorId[FEEDER_MOTOR],Hard_Hiz);
             RemoveControlCallback(ControlId, ThreadLoadControlCBFunction );
             ControlId = 0xFF;
-        }
-        //REPORT_MSG(MotorId, "Thread_Load_Dryer_Loading_Callback Motor Id");
+        }*/
         MotorMovetoEncoderPosition(HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM,Thread_Load_Dryer_MovetoEncoderPosition_Callback,10000);
         return OK;
     }
@@ -428,14 +455,17 @@
     uint32_t Thread_Load_Dryer_Loading(void)
     {
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
-        LoadArmInfo.LoadArmRounds = 20;
-        uint32_t numberOfSteps = 0;
+        LoadArmInfo.LoadArmRounds = (int)dryerbufferlength;
+        //LoadArmInfo.LoadArmRounds = 5;
+        float numberOfSteps = 0;
         //Start Feeder Pid, Rotate Loading Arm Counter Thread Direction X Circles According To Rml. Feeder Speed Is 40
         SetOriginMotorSpeed(19);
 //        OriginalMotorSpd_2PPS[FEEDER_MOTOR] = 1000;
 //        CurrentControlledSpeed[FEEDER_MOTOR] = 1000;
 
         numberOfSteps = MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround*LoadArmInfo.LoadArmRounds*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].microstep*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulleyradius;
+        numberOfSteps -= 100;
+        //numberOfSteps = MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround*3.3*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].microstep*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulleyradius;
         Report("Thread Load State Machine step.",__FILE__,LoadStages,numberOfSteps,RpMessage,(int)(MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].microstep*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulleyradius),0);
         MotorControlConfig[FEEDER_MOTOR].m_params.MAX = 1;
         MotorControlConfig[FEEDER_MOTOR].m_params.MIN = MotorsControl[FEEDER_MOTOR].outputproportionalpowerlimit*-1;
@@ -459,14 +489,16 @@
         MotorSetMaxSpeed (HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround/4);
 
         ControlId = AddControlCallback(ThreadLoadControlCBFunction, eOneMillisecond,Control_Read_Dancer_Position,(IfTypeThread*0x100+FEEDER_MOTOR),FEEDER_DANCER,FEEDER_MOTOR);
+        Report("AddControlCallback feeder",__FILE__,__LINE__,ControlId,RpMessage,IfTypeThread*0x100+FEEDER_MOTOR,0);
         CallbackCounter++;
+        Report("Thread_Load_Dryer_Loading",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
         MotorMoveWithCallback (HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].directionthreadwize,
                                numberOfSteps,    Thread_Load_Dryer_Loading_Callback, 100000);
 
         //Keep Notation How Many Rotations In The Dryer
         //LoadArmInfo.LoadArmBackLash = 0;
-        LoadArmInfo.LoadArmRounds = 0xFF;
-        FileWrite(&LoadArmInfo, sizeof(LoadArmInfo),LoadArmPath);
+        LoadArmInfo.LoadArmRounds = (int)dryerbufferlength;
+        //FileWrite(&LoadArmInfo, sizeof(LoadArmInfo),LoadArmPath,BIOS_WAIT_FOREVER);
         return OK;
     }
     uint32_t Thread_Load_Jog_ThreadStop(uint32_t index, uint32_t ReadValue)
@@ -490,6 +522,25 @@
     uint32_t Thread_Load_End(void)
     {
         REPORT_MSG(LoadStages,"Loading Ended");
+        if(ControlId != 0xFF)
+        {
+            MotorStop(ThreadMotorIdToMotorId[FEEDER_MOTOR],Hard_Hiz);
+            RemoveControlCallback(ControlId, ThreadLoadControlCBFunction );
+            ControlId = 0xFF;
+        }
+        if(PullerControlId != 0xFF)
+        {
+            MotorStop(ThreadMotorIdToMotorId[POOLER_MOTOR],Hard_Hiz);
+            RemoveControlCallback(PullerControlId, ThreadLoadControlCBFunction );
+            PullerControlId = 0xFF;
+        }
+        if(WinderControlId != 0xFF)
+        {
+            MotorStop(ThreadMotorIdToMotorId[WINDER_MOTOR],Hard_Hiz);
+            RemoveControlCallback(WinderControlId, ThreadLoadControlCBFunction );
+            WinderControlId = 0xFF;
+        }
+        LoadStages = THREAD_LOAD_INIT;
         return OK;
     }
     uint32_t Thread_Load_Dryer_UnLoading(void)
@@ -507,7 +558,7 @@
         MotorControlConfig[POOLER_MOTOR].m_params.MIN = MotorsControl[POOLER_MOTOR].outputproportionalpowerlimit*-1;
         MotorControlConfig[POOLER_MOTOR].m_params.Kd = MotorsControl[POOLER_MOTOR].derivativetime;
         MotorControlConfig[POOLER_MOTOR].m_params.Kp = MotorsControl[POOLER_MOTOR].proportionalgain;
-        MotorControlConfig[POOLER_MOTOR].m_params.Ki = MotorsControl[POOLER_MOTOR].integraltime;
+        MotorControlConfig[POOLER_MOTOR].m_params.Ki = 0;//MotorsControl[POOLER_MOTOR].integraltime;
         MotorControlConfig[POOLER_MOTOR].m_params.IntegralErrorMultiplier = MotorsControl[POOLER_MOTOR].setpointramprateorsoftstartramp;
         MotorControlConfig[POOLER_MOTOR].m_params.ProportionalErrorMultiplier = MotorsControl[POOLER_MOTOR].outputonoffhysteresisvalue;
         MotorControlConfig[POOLER_MOTOR].m_params.epsilon = MotorsControl[POOLER_MOTOR].epsilon;
@@ -523,12 +574,13 @@
         MotorSetDirection(HARDWARE_MOTOR_TYPE__MOTO_LDRIVING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_LDRIVING].directionthreadwize);
 
         PullerControlId = AddControlCallback(ThreadLoadControlCBFunction, eOneMillisecond,Control_Read_Dancer_Position,(IfTypeThread*0x100+POOLER_MOTOR),POOLER_DANCER,POOLER_MOTOR);
+        Report("AddControlCallback Puller",__FILE__,__LINE__,PullerControlId,RpMessage,IfTypeThread*0x100+POOLER_MOTOR,0);
 ////////////////////////
         MotorControlConfig[WINDER_MOTOR].m_params.MAX = 1;
         MotorControlConfig[WINDER_MOTOR].m_params.MIN = MotorsControl[WINDER_MOTOR].outputproportionalpowerlimit*-1;
         MotorControlConfig[WINDER_MOTOR].m_params.Kd = MotorsControl[WINDER_MOTOR].derivativetime;
         MotorControlConfig[WINDER_MOTOR].m_params.Kp = MotorsControl[WINDER_MOTOR].proportionalgain;
-        MotorControlConfig[WINDER_MOTOR].m_params.Ki = MotorsControl[WINDER_MOTOR].integraltime;
+        MotorControlConfig[WINDER_MOTOR].m_params.Ki = 0;//MotorsControl[WINDER_MOTOR].integraltime;
         MotorControlConfig[WINDER_MOTOR].m_params.IntegralErrorMultiplier = MotorsControl[WINDER_MOTOR].setpointramprateorsoftstartramp;
         MotorControlConfig[WINDER_MOTOR].m_params.ProportionalErrorMultiplier = MotorsControl[WINDER_MOTOR].outputonoffhysteresisvalue;
         MotorControlConfig[WINDER_MOTOR].m_params.epsilon = MotorsControl[WINDER_MOTOR].epsilon;
@@ -544,6 +596,7 @@
         MotorSetDirection(HARDWARE_MOTOR_TYPE__MOTO_WINDER,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_WINDER].directionthreadwize);
 
         WinderControlId = AddControlCallback(ThreadLoadControlCBFunction, eOneMillisecond,Control_Read_Dancer_Position,(IfTypeThread*0x100+WINDER_MOTOR),WINDER_DANCER,WINDER_MOTOR);
+        Report("AddControlCallback Winder",__FILE__,__LINE__,WinderControlId,RpMessage,IfTypeThread*0x100+WINDER_MOTOR,0);
 
 ////////////////////////
         MotorSetDirection(HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING].directionthreadwize);
@@ -553,19 +606,23 @@
         //MotorMoveWithCallback (HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].directionthreadwize,
         //                       numberOfSteps,    Thread_Load_Dryer_Loading_Callback, 100000);
         Report("Thread_Load_Set_Load_Arm_To_Start_Position",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0);
+        LoadArmInfo.LoadArmBackLash = 5;
+
         status |= MotorMoveToStopper(HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, (1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].directionthreadwize),
                                         MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround/4, Thread_Load_Set_Load_Arm_To_Stopper_Callback,LoadArmInfo.LoadArmBackLash,1000);
 
         //Keep Notation How Many Rotations In The Dryer
         //LoadArmInfo.LoadArmBackLash = 0;
-        LoadArmInfo.LoadArmRounds = 0xFF;
-        FileWrite(&LoadArmInfo, sizeof(LoadArmInfo),LoadArmPath);
+        LoadArmInfo.LoadArmRounds = (int)dryerbufferlength;
+        FileWrite(&LoadArmInfo, sizeof(LoadArmInfo),LoadArmPath,BIOS_WAIT_FOREVER);
         return OK;
     }
 
     uint32_t ThreadLoadStateMachine( THREAD_LOAD_STAGES_ENUM ReadValue)
     {
         REPORT_MSG(ReadValue,"ThreadLoadStateMachine");
+        if (LoadStages!=ReadValue)
+            LoadStages = ReadValue;
         switch (ReadValue)
         {
         case THREAD_LOAD_INIT:
@@ -613,10 +670,6 @@
             //LoadStages++;
             Thread_Load_Close_Lids();
             break;
-        case THREAD_LOAD_RESUME_HEATING:
-            //LoadStages++;
-            Thread_Load_Resume_Heating();
-            break;
         case THREAD_LOAD_JOG_FEEDER_TO_MIDDLE_POINT://JOG THE FEEDER MOTOR UNTIL THE FEEDER DANCER IS AT MIDDLE POSITION
             //LoadStages++;
             Thread_Load_Jog_Feeder_To_Middle_Point();
@@ -626,6 +679,10 @@
             //LoadStages++;
             Thread_Load_Dryer_Loading();
             break;
+        case THREAD_LOAD_RESUME_HEATING:
+            //LoadStages++;
+            Thread_Load_Resume_Heating();
+            break;
         case THREAD_LOAD_JOG_THREAD: //JOG THREAD SHORTLY TO MAKE SURE SPOOL IS RUNNING. REPORT END OF LOADING
             //LoadStages++;
             Thread_Load_Jog_Thread();
@@ -640,6 +697,20 @@
     }
     return OK;
 }
+uint32_t ThreadLoadButton(THREAD_LOAD_STAGES_ENUM ReadValue)
+{
+    Report("ThreadLoadButton",__FILE__,__LINE__,LoadStages,RpMessage,ReadValue,0);
+    if (LoadStages > ReadValue)
+    {
+        ThreadLoadStateMachine(LoadStages+1);
+    }
+    else
+    {
+        ThreadLoadStateMachine(ReadValue);
+    }
+    return OK;
+}
+uint32_t LoadCounter = 0;
 
 uint32_t ThreadLoadControlCBFunction(uint32_t IfIndex, uint32_t ReadValue)
 {
@@ -699,6 +770,11 @@ uint32_t ThreadLoadControlCBFunction(uint32_t IfIndex, uint32_t ReadValue)
         CurrentControlledSpeed[index] = calculated_speed;
         MotorSetSpeed(ThreadMotorIdToMotorId[index], calculated_speed);
     }
+/*    LoadCounter++;
+    if ((LoadCounter % 5001) == 0)
+    {
+          Report("MotorSpeedUpdated",__FILE__,index,abs(TranslatedReadValue),RpWarning,(int)CurrentControlledSpeed[index],0);
+    }*/
  return OK;
 }
 void ThreadLoadRequest(MessageContainer* requestContainer)