Merge branch 'master' of https://twinetfs.visualstudio.com/Tango/_git/Tango

1 files changed, 8 insertions, 8 deletions

diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
index f13f76cfb..25f322b2e 100644
--- a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
+++ b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
@@ -337,7 +337,7 @@ uint32_t PoolerThreadLengthCBFunction(uint32_t IfIndex, uint32_t ReadValue)
         }**/
 
     //}
-#ifdef FOUR_WINDERS
+#ifdef BTSR_NO_TFU
         if (CurrentControlledSpeed[WINDER_MOTOR]>100)
             length = dyeingspeed/10;
 #endif
@@ -914,7 +914,7 @@ uint32_t Release_Right_TFU_TensionCallback(uint32_t deviceID, uint32_t BusyFlag)
 uint32_t Release_Right_TFU_Tension()
 {
     uint32_t status = OK;
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
     if (RTFU_Up == true)
     {
         Report("Release_Right_TFU_Tension",__FILE__,__LINE__,HARDWARE_MOTOR_TYPE__MOTO_RDANCER,RpMessage,MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDANCER].pulseperround/4,0);
@@ -928,7 +928,7 @@ int SecondFeederCorrection = 4;
 int PrepareWaitCount = 0;
 uint32_t Adjust_Right_TFU_Tension_2nd_Callback(uint32_t MotorId, uint32_t ReadValue)
 {
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
     MotorStop (HARDWARE_MOTOR_TYPE__MOTO_RDANCER,Soft_Stop); //per L6470 errata between mov and run commands
     Report("Adjust_Right_TFU_Tension_2ndCallback x more steps",__FILE__,__LINE__,MotorId,RpMessage,SecondFeederCorrection,0);
     if (JobIsActive()==false)
@@ -952,7 +952,7 @@ uint32_t Adjust_Right_TFU_Tension_2nd_Callback(uint32_t MotorId, uint32_t ReadVa
 }
 uint32_t Adjust_Right_TFU_Tension_Callback(uint32_t MotorId, uint32_t ReadValue)
 {
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
     Report("Adjust_Right_TFU_Tension_Callback",__FILE__,__LINE__,MotorId,RpMessage,0,0);
     MotorMoveWithCallback(HARDWARE_MOTOR_TYPE__MOTO_RDANCER, 1-MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDANCER].directionthreadwize,SecondFeederCorrection* MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDANCER].microstep, Adjust_Right_TFU_Tension_2nd_Callback,1000);
     RTFU_Up = true;
@@ -963,7 +963,7 @@ uint32_t Adjust_Right_TFU_Tension_Callback(uint32_t MotorId, uint32_t ReadValue)
 uint32_t Adjust_Right_TFU_Tension(double tension)
 {
     uint32_t status = OK;
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
     if (tension > 0.5) //0 = lower position, 1 = high position
     {
         if (FPGA_Read_limit_Switches(GPI_LS_RDANCER_UP) == NO_LIMIT)
@@ -1090,7 +1090,7 @@ uint32_t ThreadPrepareState(void *JobDetails)
     IntersegmentLength = JobTicket->intersegmentlength;
 
     PrepareWaitCount = 0;
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
     status = ThreadPrepare_Tension (HARDWARE_DANCER_TYPE__LeftDancer, windertension);
     ReportWithPackageFilter(ThreadFilter,"ThreadPrepare_Tension Winder",__FILE__,HARDWARE_DANCER_TYPE__LeftDancer,PrepareWaitCount,RpWarning,(int)windertension,0);
     status = ThreadPrepare_Tension (HARDWARE_DANCER_TYPE__MiddleDancer, pullertension);
@@ -1212,7 +1212,7 @@ uint32_t ThreadPrepareState(void *JobDetails)
 /////////////////////////////////////////////////////
         MotorSetDirection((TimerMotors_t)HW_Motor_Id,MotorsCfg[HW_Motor_Id].directionthreadwize);
 
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
         if (Motor_i == FEEDER_MOTOR) // dryer motor is speed controlled. later a speed sensor will be utilized, but for now it will not be controlled
         {
             ReportWithPackageFilter(ThreadFilter,"Feeder Control",__FILE__,Motor_i,MotorControlConfig[Motor_i].m_params.Kp,RpWarning,MotorControlConfig[Motor_i].m_params.Ki,0);
@@ -1239,7 +1239,7 @@ uint32_t ThreadPrepareState(void *JobDetails)
             PoolerLengthCalculationMultiplier = (MotorsCfg[ThreadMotorIdToMotorId[Motor_i]].pulleyradius*2*PI)/(MotorsCfg[ThreadMotorIdToMotorId[Motor_i]].pulseperround*MotorsCfg[ThreadMotorIdToMotorId[Motor_i]].microstep);
             PoolerSpeedControlId = AddControlCallback(NULL,PoolerThreadLengthCBFunction, eHundredMillisecond,MotorGetPositionFromFPGA,(IfTypeThread*0x100+Motor_i),ThreadMotorIdToMotorId[Motor_i],Motor_i);
         }
-#ifndef FOUR_WINDERS
+#ifndef BTSR_NO_TFU
             if (Motor_i == FEEDER_MOTOR) // dryer motor is speed controlled. later a speed sensor will be utilized, but for now it will not be controlled
             {
                 if (ControlIdtoMotorId[Motor_i] != 0xFF)