fixes, add dryer control support

2 files changed, 10 insertions, 6 deletions

diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
index 25c36f3fd..0aff26320 100644
--- a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
+++ b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c
@@ -685,7 +685,7 @@
         LengthCalculationMultiplier = (MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDRIVING].pulleyradius*2*PI)/(MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDRIVING].pulseperround*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_RDRIVING].microstep);
         TotalLoadedLen = 0;
         DrierPrevLocation = 200; //initial safe value
-        SpeedTControlId = AddControlCallback(ThreadLoadLengthCBFunction, eHundredMillisecond,MotorGetPositionFromFPGA,(IfTypeThread*0x100+HARDWARE_MOTOR_TYPE__MOTO_RDRIVING),HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,0);
+        SpeedTControlId = AddControlCallback("Thread length",ThreadLoadLengthCBFunction, eHundredMillisecond,MotorGetPositionFromFPGA,(IfTypeThread*0x100+HARDWARE_MOTOR_TYPE__MOTO_RDRIVING),HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,0);
         Tinitialpos = 0xFFFF;previousPosition = 0; currentPosition = 0;
         CallbackCounter++;
         Report("Thread_Load_Dryer_Loading",__FILE__,__LINE__,LoadStages,RpMessage,CallbackCounter,0);
@@ -713,7 +713,7 @@
     {
         REPORT_MSG(LoadStages, "Thread Load State Machine step");
         ThreadJoggingFunc(20);
-        LoadingControlId = AddControlCallback(Thread_Load_Jog_ThreadStop, eOneSecond*25,Control_Read_Dancer_Position,(IfTypeThread*0x100+FEEDER_MOTOR),FEEDER_DANCER,FEEDER_MOTOR);
+        LoadingControlId = AddControlCallback("Load jog",Thread_Load_Jog_ThreadStop, eOneSecond*25,Control_Read_Dancer_Position,(IfTypeThread*0x100+FEEDER_MOTOR),FEEDER_DANCER,FEEDER_MOTOR);
         return OK;
     }
     uint32_t Thread_Load_End(void)
@@ -1155,7 +1155,7 @@ uint32_t ThreadLoadControlCBFunction(uint32_t IfIndex, uint32_t ReadValue)
 
     NormalizedError = avreageSampleValue*NormalizedErrorCoEfficient[index];
     MotorControlConfig[index].m_mesuredParam = NormalizedError;
-    MotorControlConfig[index].m_calculatedError = AdvancedPIDAlgorithmCalculation((float)MotorControlConfig[index].m_SetParam , (float)MotorControlConfig[index].m_mesuredParam,
+    MotorControlConfig[index].m_calculatedError = PIDAlgorithmCalculation((float)MotorControlConfig[index].m_SetParam , (float)MotorControlConfig[index].m_mesuredParam,
                                                                           &MotorControlConfig[index].m_params,   &MotorControlConfig[index].m_preError, &MotorControlConfig[index].m_integral);
     if (index != FEEDER_MOTOR) //feeder unit handles errors opposite to left unit
     {
diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
index 0a3a9e149..45ab2cb19 100644
--- a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
+++ b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_print.c
@@ -41,7 +41,11 @@
 
 double CurrentControlledSpeed[MAX_THREAD_MOTORS_NUM] = {0};
 
+#ifndef DRIER_CONTROL_TEST
+TimerMotors_t ThreadMotorIdToMotorId[MAX_THREAD_MOTORS_NUM] = {HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,HARDWARE_MOTOR_TYPE__MOTO_LDRIVING,HARDWARE_MOTOR_TYPE__MOTO_WINDER,HARDWARE_MOTOR_TYPE__MOTO_SCREW};
+#else
 TimerMotors_t ThreadMotorIdToMotorId[MAX_THREAD_MOTORS_NUM] = {HARDWARE_MOTOR_TYPE__MOTO_RDRIVING,HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,HARDWARE_MOTOR_TYPE__MOTO_LDRIVING,HARDWARE_MOTOR_TYPE__MOTO_WINDER,HARDWARE_MOTOR_TYPE__MOTO_SCREW};
+#endif
 HardwareDancerType ThreadMotorIdToDancerId[MAX_THREAD_MOTORS_NUM] = {FEEDER_DANCER,NUM_OF_DANCERS,POOLER_DANCER,WINDER_DANCER,NUM_OF_DANCERS};
 uint32_t    ControlIdtoMotorId [MAX_THREAD_MOTORS_NUM] = {0xFF,0xFF,0xFF,0xFF,0xFF};
 uint32_t    SpeedControlId=0xFF;
@@ -848,7 +852,7 @@ uint32_t ThreadInitialTestStub(HardwareMotor * request)
             }
 //            if (HW_Motor_Id == HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING) // dryer motor is speed controlled. later a speed sensor will be utilized, but for now it will not be controlled
 //                AddControlCallback(ThreadSpeedControlCBFunction, eOneMillisecond,TemplateDataReadCBFunction,(IfTypeThread*0x100+Motor_i),ThreadMotorIdToMotorId[Motor_i],0);
-            if (Motor_i == HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING) // dryer motor is speed controlled. later a speed sensor will be utilized, but for now it will not be controlled
+            if (Motor_i == ThreadMotorIdToMotorId[DRYER_MOTOR]) // dryer motor is speed controlled. later a speed sensor will be utilized, but for now it will not be controlled
                 continue;
     }
 #ifdef TEST_PID_THREAD
@@ -897,7 +901,7 @@ uint32_t ThreadDryerRampUp(uint32_t IfIndex, uint32_t BusyFlag)
         ControlIdtoMotorId[DRYER_MOTOR] = 0xFF;
     }
 
-    MotorSetSpeed(HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,InitialDryerSpeed );
+    MotorSetSpeed(ThreadMotorIdToMotorId[DRYER_MOTOR],InitialDryerSpeed );
     //ReportWithPackageFilter(ThreadFilter,"ThreadDryerRampUp",__FILE__,ControlIdtoMotorId[DRYER_MOTOR],(int)InitialDryerSpeed,RpWarning,(int)OriginalMotorSpd_2PPS[DRYER_MOTOR],0);
 
 
@@ -927,7 +931,7 @@ uint32_t ThreadPreSegmentState(void *SegmentDetails, uint32_t SegmentId)
         DrierDivider = dyeingspeed/5;  //ramp up drier in 5 cm/sec steps
         ReportWithPackageFilter(ThreadFilter,"Drier ramp up",__FILE__,__LINE__,(int)dyeingspeed,RpWarning,(int)DrierDivider,0);
         InitialDryerSpeed = OriginalMotorSpd_2PPS[DRYER_MOTOR]/DrierDivider;
-        MotorSetSpeed(HARDWARE_MOTOR_TYPE__MOTO_DRYER_DRIVING,InitialDryerSpeed );
+        MotorSetSpeed(ThreadMotorIdToMotorId[DRYER_MOTOR],InitialDryerSpeed );
         ControlIdtoMotorId[DRYER_MOTOR] = AddControlCallback("DryerRampUp",ThreadDryerRampUp, 200,TemplateDataReadCBFunction,0,0,0);
 #endif
 #ifdef HUNDRED_MICROSECONDS_DANCER_READ