diff options
Diffstat (limited to 'Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c')
| -rw-r--r-- | Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c | 35 |
1 files changed, 18 insertions, 17 deletions
diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c index a82fe37e6..74a07e99c 100644 --- a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c +++ b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c @@ -38,21 +38,21 @@ /* typedef enum { 0 THREAD_LOAD_INIT, - 1 THREAD_LOAD_REDUCE_HEAT, //HEATERS OFF, DRYER BLOWER OFF, BLOWER LOW, - 2 THREAD_LOAD_SET_LOAD_ARM_TO_START_POSITION,//USE NOTATION HOW MANY ROTATIONS IN THE DRYER, OR CHECK AGAINST STOPPER. MOVE SLOWLY - 3 THREAD_LOAD_CENTER_HEAD_ROCKERS, //puthead cleaning rockers to middle position - 4 THREAD_LOAD_OPEN_COVERS, //OPEN DYEING HEAD COVER AND DRYER LID + 1 THREAD_LOAD_REDUCE_HEAT, //HEATERS OFF, DRYER BLOWER OFF, BLOWER LOW, + 2 THREAD_LOAD_SET_LOAD_ARM_TO_START_POSITION, //USE NOTATION HOW MANY ROTATIONS IN THE DRYER, OR CHECK AGAINST STOPPER. MOVE SLOWLY + 3 THREAD_LOAD_CENTER_HEAD_ROCKERS, //puthead cleaning rockers to middle position + 4 THREAD_LOAD_OPEN_COVERS, //OPEN DYEING HEAD COVER AND DRYER LID 5 THREAD_LOAD_LIFT_DANCERS, - 6 THREAD_LOAD_LIFT_ROCKERS, //MACHINE IS READY. SEND MESSAGE, START TIMER TO CLOSE LIDS, WAIT FOR OPERATOR RESPONSE - 7 THREAD_LOAD_INITIAL_TENSION,//CHECK SPOOL PRESENCERUN WINDER UNTIL BREAK SENSOR IS IDENTIFIEING MOVEMENT FOR A SECOND + 6 THREAD_LOAD_LIFT_ROCKERS, //MACHINE IS READY. SEND MESSAGE, START TIMER TO CLOSE LIDS, WAIT FOR OPERATOR RESPONSE + 7 THREAD_LOAD_INITIAL_TENSION, //CHECK SPOOL PRESENCERUN WINDER UNTIL BREAK SENSOR IS IDENTIFIEING MOVEMENT FOR A SECOND 8 THREAD_LOAD_CLOSE_ROCKERS, - 9 THREAD_LOAD_CLOSE_DANCERS, //SEND DANCER MOTORS TO PRESET LOCATION, CHECK THAT THE DANCERS ARE ON THE THREAD + 9 THREAD_LOAD_CLOSE_DANCERS, //SEND DANCER MOTORS TO PRESET LOCATION, CHECK THAT THE DANCERS ARE ON THE THREAD 10 THREAD_LOAD_CLOSE_LIDS, 11 THREAD_LOAD_RESUME_HEATING, - 12 THREAD_LOAD_JOG_FEEDER_TO_MIDDLE_POINT,//JOG THE FEEDER MOTOR UNTIL THE FEEDER DANCER IS AT MIDDLE POSITION - 13 THREAD_LOAD_DRYER_LOADING, //START FEEDER PID, ROTATE LOADING ARM COUNTER THREAD DIRECTION X CIRCLES ACCORDING TO RML. FEEDER SPEED IS 40 - //KEEP NOTATION HOW MANY ROTATIONS IN THE DRYER - 14 THREAD_LOAD_JOG_THREAD, //JOG THREAD SHORTLY TO MAKE SURE SPOOL IS RUNNING. REPORT END OF LOADING + 12 THREAD_LOAD_JOG_FEEDER_TO_MIDDLE_POINT, //JOG THE FEEDER MOTOR UNTIL THE FEEDER DANCER IS AT MIDDLE POSITION + 13 THREAD_LOAD_DRYER_LOADING, //START FEEDER PID, ROTATE LOADING ARM COUNTER THREAD DIRECTION X CIRCLES ACCORDING TO RML. FEEDER SPEED IS 40 + //KEEP NOTATION HOW MANY ROTATIONS IN THE DRYER + 14 THREAD_LOAD_JOG_THREAD, //JOG THREAD SHORTLY TO MAKE SURE SPOOL IS RUNNING. REPORT END OF LOADING 15 THREAD_LOAD_END }THREAD_LOAD_STAGES_ENUM;*/ THREAD_LOAD_STAGES_ENUM LoadStages = THREAD_LOAD_INIT; @@ -222,9 +222,9 @@ else { LoadStages++; - if (LoadStages != THREAD_LOAD_INITIAL_TENSION) //on this satge we should wait for user call + if (LoadStages != THREAD_LOAD_INITIAL_TENSION) //on this stage we should wait for user call { - ThreadLoadStateMachine(LoadStages); + //ThreadLoadStateMachine(LoadStages); } } } @@ -340,7 +340,7 @@ { Control_Dryer_Fan(START,75);//use START or STOP, 0 - 100% LoadStages++; - ThreadLoadStateMachine(LoadStages); + //ThreadLoadStateMachine(LoadStages); } return OK; } @@ -357,6 +357,7 @@ { Report("Thread Load State Machine Callback.",__FILE__,__LINE__,LoadStages,RpMessage,NumberOfDrierLoaderCycles,0); REPORT_MSG(MotorId, "Thread_Load_Dryer_Loading_Callback Motor Id"); + MotorMovetoEncoderPosition(HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM,0,0); if(ControlId != 0xFF) { MotorStop(ThreadMotorIdToMotorId[FEEDER_MOTOR],Hard_Hiz); @@ -371,7 +372,7 @@ LoadStages++; if (LoadStages != THREAD_LOAD_INITIAL_TENSION) //on this satge we should wait for user call { - ThreadLoadStateMachine(LoadStages); + //ThreadLoadStateMachine(LoadStages); } } } @@ -417,7 +418,7 @@ //Keep Notation How Many Rotations In The Dryer //LoadArmInfo.LoadArmBackLash = 0; - //LoadArmInfo.LoadArmRounds = 0xFF; + LoadArmInfo.LoadArmRounds = 0xFF; FileWrite(&LoadArmInfo, sizeof(LoadArmInfo),LoadArmPath); return OK; } @@ -428,7 +429,7 @@ ControlId = 0xFF; ThreadAbortJoggingFunc(); LoadStages++; - ThreadLoadStateMachine(LoadStages); + //ThreadLoadStateMachine(LoadStages); return OK; } uint32_t Thread_Load_Jog_Thread(void) |