diff options
Diffstat (limited to 'Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c')
| -rw-r--r-- | Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c | 15 |
1 files changed, 10 insertions, 5 deletions
diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c index a116bbd66..0bc2d04de 100644 --- a/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c +++ b/Software/Embedded_SW/Embedded/Modules/Thread/ThreadLoad.c @@ -35,7 +35,7 @@ //#include <stdint.h> //#include <stdbool.h> - typedef enum +/* typedef enum { THREAD_LOAD_INIT, THREAD_LOAD_REDUCE_HEAT, //HEATERS OFF, DRYER BLOWER OFF, BLOWER LOW, @@ -54,7 +54,7 @@ //KEEP NOTATION HOW MANY ROTATIONS IN THE DRYER THREAD_LOAD_JOG_THREAD, //JOG THREAD SHORTLY TO MAKE SURE SPOOL IS RUNNING. REPORT END OF LOADING THREAD_LOAD_END - }THREAD_LOAD_STAGES_ENUM; + }THREAD_LOAD_STAGES_ENUM;*/ THREAD_LOAD_STAGES_ENUM LoadStages = THREAD_LOAD_INIT; ProcessParameters ProcessParametersClear,ProcessParametersRecover; uint8_t NumberOfDrierLoaderCycles = 0; @@ -69,7 +69,7 @@ uint32_t LoadArmBackLash; }LoadArmInfoStruc; LoadArmInfoStruc LoadArmInfo; - char LoadArmPath[50] = "0://SWInfo//LoadArm.msg"; + char LoadArmPath[50] = "0://SysInfo//LoadArm.cfg"; //RUN MOTOR TO SWITCH WITH TIMEOUT //RUN MOTOR TO BREAK SENSOR @@ -211,7 +211,10 @@ if (CallbackCounter == 0) { LoadStages++; - //ThreadLoadStateMachine(LoadStages); + if (LoadStages != THREAD_LOAD_INITIAL_TENSION) //on this satge we should wait for user call + { + //ThreadLoadStateMachine(LoadStages); + } } } else @@ -341,12 +344,14 @@ { REPORT_MSG(LoadStages, "Thread Load State Machine step"); LoadArmInfo.LoadArmRounds = 20; + uint32_t numberOfSteps = 0; //Start Feeder Pid, Rotate Loading Arm Counter Thread Direction X Circles According To Rml. Feeder Speed Is 40 OriginalMotorSpd_2PPS[FEEDER_MOTOR] = 1000; + numberOfSteps = MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround*LoadArmInfo.LoadArmRounds*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].microstep*MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulleyradius; ControlId = AddControlCallback(ThreadLoadControlCBFunction, eOneMillisecond,Control_Read_Dancer_Position,(IfTypeThread*0x100+FEEDER_MOTOR),FEEDER_DANCER,FEEDER_MOTOR); CallbackCounter++; MotorMoveWithCallback (HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM, MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].directionthreadwize, - MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_DRYER_LOADARM].pulseperround*LoadArmInfo.LoadArmRounds, Thread_Load_HomingCallback, 100000); + numberOfSteps, Thread_Load_HomingCallback, 100000); //Keep Notation How Many Rotations In The Dryer //LoadArmInfo.LoadArmBackLash = 0; |