diff options
Diffstat (limited to 'Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c')
| -rw-r--r-- | Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c | 10 |
1 files changed, 5 insertions, 5 deletions
diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c index 510168ab8..7e1312464 100644 --- a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c +++ b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c @@ -321,7 +321,7 @@ uint32_t Screw100msecDirectionChange(uint32_t deviceID, uint32_t BusyFlag) { ScrewNumberOfSteps--; WindingConeLocation--; - ReportWithPackageFilter(ThreadFilter,"Head Backing",__FILE__,__LINE__,CalculationDirectionChangeCounter,RpWarning,ScrewNumberOfSteps, 0); + // ReportWithPackageFilter(ThreadFilter,"Head Backing",__FILE__,__LINE__,CalculationDirectionChangeCounter,RpWarning,ScrewNumberOfSteps, 0); } } else //next time going back @@ -329,7 +329,7 @@ uint32_t Screw100msecDirectionChange(uint32_t deviceID, uint32_t BusyFlag) if ((CalculationDirectionChangeCounter/2)%InternalWinderCfg.SpoolBottomBackingRate == 0) { ScrewNumberOfSteps++; - Report("Bottom Backing ",__FILE__,__LINE__,CalculationDirectionChangeCounter,RpWarning,ScrewNumberOfSteps, 0); + // Report("Bottom Backing ",__FILE__,__LINE__,CalculationDirectionChangeCounter,RpWarning,ScrewNumberOfSteps, 0); } } /* if (WinderMotorSpeedRollOver) @@ -364,11 +364,11 @@ uint32_t Screw100msecDirectionChange(uint32_t deviceID, uint32_t BusyFlag) ScrewRunningTime = temp;//(SYS_CLK_FREQ*Steps)/ScrewSpeed; //ROM_IntMasterEnable(); //usnprintf(TempScrewStr, 100, "Winder: Horizon,Rotation, PPR, RPP{ %d, %d ,%d, %d} ",(int)screw_horizontal_speed,(int)RotationsPerSecond,(int)InternalWinderCfg.NumberOfRotationPerPassage,(int)MotorsCfg[HARDWARE_MOTOR_TYPE__MOTO_WINDER].pulseperround); - usnprintf(ScrewStr, 100, "Winder: Steps,Speed, Time, WinderSpeed{ %d, %d ,%d, %d} ",(int)ScrewNumberOfSteps,(int)ScrewSpeed,(int)temp,(int)WinderReferenceSpeed); +// usnprintf(ScrewStr, 100, "Winder: Steps,Speed, Time, WinderSpeed{ %d, %d ,%d, %d} ",(int)ScrewNumberOfSteps,(int)ScrewSpeed,(int)temp,(int)WinderReferenceSpeed); // Report(logmsg[index],__FILE__,__LINE__,index,RpWarning,index, Counter[index]); // #warning PID is now only proportional (above) //Report(TempScrewStr,__FILE__,__LINE__,0,RpWarning,0, 0); - Report(ScrewStr,__FILE__,__LINE__,ScrewCurrentDirection,RpWarning,CalculationDirectionChangeCounter, 0); +// Report(ScrewStr,__FILE__,__LINE__,ScrewCurrentDirection,RpWarning,CalculationDirectionChangeCounter, 0); //REPORT_MSG(temp , "new winder speed"); //Report("new winder speed",__FILE__,ScrewNumberOfSteps,temp,RpWarning,ScrewSpeed,0); } @@ -535,7 +535,7 @@ uint32_t ScrewDTSCallback(uint32_t deviceID, uint32_t BusyFlag) } uint32_t WinderDistanceToSpoolState(void ) { - double DTS_Time = ((dryerbufferlength*100)/dyeingspeed)*1000;//distance to spool time in milliseconds + double DTS_Time = (dryerbufferCentimeters/dyeingspeed)*1000;//distance to spool time in milliseconds REPORT_MSG ((int)DTS_Time,"WinderDistanceToSpoolState"); ScrewDTSControlId = AddControlCallback(ScrewDTSCallback, DTS_Time-WinderBackToBaseTime,TemplateDataReadCBFunction,0,0,0); |