diff options
Diffstat (limited to 'Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c')
| -rw-r--r-- | Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c | 12 |
1 files changed, 6 insertions, 6 deletions
diff --git a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c index 22fcf3e6f..d92e6a330 100644 --- a/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c +++ b/Software/Embedded_SW/Embedded/Modules/Thread/Thread_Winder.c @@ -220,7 +220,7 @@ uint32_t Screw100msecDirectionChange(uint32_t deviceID, uint32_t BusyFlag) winderspeed+=WinderMotorSpeed[i]; } winderspeed/=MAX_WINDER_SPEED_CALCULATION; - //LOG_ERROR(winderspeed, "WinderSpeedUpdated"); + //REPORT_MSG(winderspeed, "WinderSpeedUpdated"); Report("WinderSpeedUpdated",__FILE__,__LINE__,winderspeed,RpWarning,ScrewNumberOfSteps,0); WinderReferenceSpeed = winderspeed; @@ -238,7 +238,7 @@ uint32_t Screw100msecDirectionChange(uint32_t deviceID, uint32_t BusyFlag) // Report(logmsg[index],__FILE__,__LINE__,index,RpWarning,index, Counter[index]); // #warning PID is now only proportional (above) Report(ScrewStr,__FILE__,__LINE__,ScrewCurrentDirection,RpWarning,CalculationDirectionChangeCounter, 0); - //LOG_ERROR(temp , "new winder speed"); + //REPORT_MSG(temp , "new winder speed"); //Report("new winder speed",__FILE__,__LINE__,temp,RpWarning,ScrewSpeed,0); } ScrewRunningTime = temp;//(SYS_CLK_FREQ*Steps)/ScrewSpeed; @@ -283,7 +283,7 @@ uint32_t Winder_Presegment(void *JobDetails, uint32_t SegmentId) //MotorSetMaxSpeed (HARDWARE_MOTOR_TYPE__MOTO_SCREW,ScrewSpeed); usnprintf(Message, 80, "SCREW speed Rot/sec %d horizon %d pulses %d",(int)RotationsPerSecond,(int)screw_horizontal_speed,(int)ScrewSpeed); - //LOG_ERROR(segmentfirst_speed,Message); + //REPORT_MSG(segmentfirst_speed,Message); //Report(Message,__FILE__,__LINE__,Dispenser_i,RpWarning,segmentfirst_speed,0); SendJobProgress(0.0,0,false, Message); @@ -299,11 +299,11 @@ uint32_t Winder_Presegment(void *JobDetails, uint32_t SegmentId) temp *= InternalWinderCfg.segmentoffsetpulses; temp /= ScrewSpeed; ScrewRunningTime = temp;//(SYS_CLK_FREQ*InternalWinderCfg.segmentoffsetpulses)/ScrewSpeed; - LOG_ERROR(ScrewNumberOfSteps,"Winder pre segment - ScrewNumberOfSteps"); - LOG_ERROR(ScrewRunningTime,"Winder pre segment - ScrewRunningTime"); + REPORT_MSG(ScrewNumberOfSteps,"Winder pre segment - ScrewNumberOfSteps"); + REPORT_MSG(ScrewRunningTime,"Winder pre segment - ScrewRunningTime"); // MotorSetDirection (HARDWARE_MOTOR_TYPE__MOTO_SCREW, ScrewCurrentDirection); //ScrewDirection = 1-ScrewDirection; - LOG_ERROR(ScrewSpeed,"Winder pre segment - ScrewSpeed"); + REPORT_MSG(ScrewSpeed,"Winder pre segment - ScrewSpeed"); //MotorSetSpeedDirect(HARDWARE_MOTOR_TYPE__MOTO_SCREW,ScrewSpeed); ScrewsStartControlTimer (); ScrewControlId = AddControlCallback(Screw100msecDirectionChange, eHundredMillisecond,TemplateDataReadCBFunction,0,0,0); |